HomeSoftware & Software SupportN1MM_ClubLog Gateway


N1MM_ClubLog Gateway — 39 Comments

  1. I have uploaded a brand new version for the gateway. The has been re-written in to get away from the various versions of XML Libraries with VB6. The interface and the workings are the same as the other version the only difference being everything now uses the .net 4.0 libraries.

    73 Rick N2AMG

    p.s. If you try to upload a test qso use a different call other than your own as ClubLog will reject this and cause the upload to fail..

  2. Hi Rick,
    thanks for this add-in. I’ll install and try with N1MM plus. I’m going to operate as T88RY.
    73 Frank i2dmi

  3. That is a false positive. I scan my files with 2 different virus scanners before I upload them to the server and my server does a virus scan every night. Because there are components that access the internet it is being flagged.

    73 Rick N2AMG

  4. Due to an unwanted PC reboot the gateway don’t work anymore.
    I try install the gateway again but it’s not working.
    Running Windows 10
    Where is the readme file ?

  5. Leon..
    Have you downloaded the Full installer and the Update below it??
    Run the full installer first and then unzip the update into the same directory as you installed the full installer.You can turn debug on and try to log a couple of qso’s in N1MM and after doing so send me the debug file and I can see where it is breaking at.

    73 Rick n2AMG

  6. Before starting, would like to ask if this utility works with N1MM+ logger too.
    There is no N1MM.ini file, but I find N1MMlogger.ini, and in that file the section that looks like this:


    Is this where to instert the lines stated in the ReadMe.txt?

  7. Hi Tom..
    Yes the gateway will work with N1MM+ I will change the title now since the old N1MM is no longer supported.

    As for the .ini file yes that is the correct .ini file but it looks like you already have the entries needed already setup.

    All you need to do is setup the gateway and add your info to it and it should upload contacts when ever one is logged in N1MM. Give it a test before you try it for the first time in a contest.

    73 Rick N2AMG

  8. Seems I get this kind of error message in the error file on all qsos:

    12.5.2017 11:29:10 – Error – ProcessXMLString
    =Error Report=
    There is no row at position 0.
    =Error Report End=

    In ClubLog it looks OK, though. What might be the problem?

    Tom OH6VDA

  9. Tom..
    Turn Debugging on and try to log another qso. When it fails turn debugging off and in the directory the gateway is installed you will find DebugLog.txt please send that to me direct to

    I have not seen this error before so I need to see the debug info to track it down..

    73 Rick N2AMG

  10. Hi Rich,
    Would you please make the little prog. to sort the callsign if the callsign has found duplicates in the same bands. it would be usefull for optimize bytes free.

    I don’t see the logger32 as well as N1MM+.

    Thanks alot !

    73 DX,

    Pri YB0ECT

  11. I have just posted an update of this utility. It adds message buffering and fixes a RunTime error that happened if the username was not entered correctly.

    Please give it a try and let me know if you find anything wrong with it..

    73 Rick N2AMG

  12. I would like to use your interface between N1MM and Clublog.
    But since I have multiple callsigns under one log-in and password.
    It will be impossible to use this interface as it will put my dxpedition logs under my home call and not under my DX call.
    Is there a workaround for this issue?

    73e Michael

  13. Michael..
    The way I have this setup is if you change the upload callsign (login call) that call will be used to place the qso’s into the correct log. Since contests are usually used by only one call at a time changing it before the contest should make things work correctly..

    73 Rick N2AMG

  14. Rick,

    Not able to download the full Install.

    Prasad VU2PTT

  15. Prasad..
    Give me a day or so and I will make sure its back online. Just no time to work on it at the moment..

    73 Rick

  16. Rick

    I’ve just installed your Gateway app but get the following errors:

    23/12/2018 18:22:48 – Club Log Error Message Returned
    =Error Report=

    The remote server returned an error: (403) Forbidden.

    23/12/2018 18:22:54 – Error – ProcessXMLString
    =Error Report=
    There is no row at position 0.
    =Error Report End=

    Am I doing something wrong?


  17. Hi Gordon..
    After you installed the first file did you install the update that is located right below it??

    73 Rick N2AMG

  18. Rick,
    I’m trying to set this up and receive this error:
    9/4/2019 10:57:34 PM – Error – Button_start_Click
    =Error Report=
    Only one usage of each socket address (protocol/network address/port) is normally permitted 0
    =Error Report End=
    I am using 12060 as you specified and the N1MM ini file has been updated.
    I’m sure it is a simple config correction but I can’t find it.

  19. I’m in the Scandinavian contest, and once in a while, a qso is not uploaded. On reoploading from the adif file, I suddenly realised that QRG is not added, only band, when uploading realtime. Is this intentional?

    73 de Tom

  20. This has been fixed but I have not built the new version yet. I don’t like the way I coded some of the upload routines so I’m looking at a different routine to use…

    73 Rick N2AMG

  21. I’m in JW5E right now, preparing for CQWW SSB, and G7VJR’s solution is too complicated. Any chance of testing your build with the fix??

    73 de Tom JW6VDA

  22. Tom..
    I have just uploaded the new file. Click on the file and when its downloaded unzip it into the current directory being used for the gateway.
    Sorry I did not get this up sooner had some issue with another piece of software I write.

    73 Rick N2AMG

  23. Rick,
    Just begin using the program for our TO9W operation and the automatic upload to CL no longer is working. I can process an ADIF file and upload it but not the automatic upload. The data does appear in the window as if it is uploading but the counter for uploaded QSOs stays at zero.

  24. I am JA7HMZ / V63DX.
    I have a question. I use N1MM + ClublogGateway.
    I registered and logged in four callsigns on Clublog.
    If you send data in real time to one of them, for example, the log of V63DX
    Should the call sign on the Gateway top screen be V63DX?
    Example) email address + V63DX + password.
    Or do I have to make settings on Clublog?
    JA7HMZ Sho

  25. You will need to change the information in the clublog information box for each call you want to work with. The Callsign is used to know where the call should be added to.

    73 Rick N2AMG

  26. Hi Rick, I’ve installed full + update and adapted the “N1MM Logger.ini” with the required broadcast info below


    I started n1mm and the gateway successfuly
    I can do a manual clublog upload, that confirms clublog login info are correct but when I log a contact in n1mm, the gateway stays inactive, displaying total qos’s uploaded:0.
    Restarting n1mm, the gateway and the computer have no effect.
    Can you helo me?


  27. Manu..
    A couple of things to check..
    1. On the main window is the indicator in the upper right corner green??
    When you log a contact in N1MM do you see the contact data in the receive window??

    73 Rick N2AMG

  28. Hi Rick,

    it is a red ‘stop’, the status at the bottom is ‘waiting…’ and the text window contains ‘Start : 20-05-20 22:59:46:433 – IP:’

    I do not see the contact data in the receive window and the total qso’s remains on 0 after logging contacts in n1mm. Something to do with security on windows?


  29. Hi Rick,
    I started tu use Clublob Gateway and works fine for livestream.
    My only question is why the frequency is not broadcasted?
    I had a look in the configuration file and can’t find if frequency broadcast is missing?
    Jacky, ZL3CW

  30. If you would turn Debug on and let it run for a few minutes capturing a couple of logged qso’s. After it is done turn debugging off and you should find a file in the install directory of the program called debuglog.txt. Send that as an attachment to

    73 Rick N2AMG

  31. Hi Mat..
    I will have to check it out when I get a chance. It will probabaly be a lit with some family health issues going on..
    73 Rick N2AMG

  32. Hi Rick,
    In version 2.0.20 manual upload OK, but, automatic return error 400.

  33. Hi Rick,
    look where I am:
    2024-04-17 7:15:58 AM – Club Log Error Message Returned
    =Error Report=

    The remote server returned an error: (403) Forbidden. 0
    Sent Data= 599 599 14.01500 20 HP1EUA CW 20240417 121542 1508 0 YB0 -1 14.01500
    YB0ECT 599 599 14.01500 20 HP1EUA CW 20240417 121542 1508 0 YB0 -1 14.01500
    =Error Report End=

    is only the regular web site login is needed?

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

HTML tags allowed in your comment: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>